SEON Trooper TL4 Installationsanleitung PDF herunterladen (Seite 2)

DVR Installation

The DVR can be installed horizontally or vertically. Do not install the DVR upside down.

Powering the System On

Turn the vehicle ignition on to power up the DVR. When the PWR LED shows green and the HDD LED flashes

red, the DVR is operating normally and recording.

DVR Menu Setup

Depending on any options installed, the DVR needs to have some menu settings updated to operate properly.

To access the DVR menu settings, connect a portable video monitor and mouse to the DVR.

DVR Menu Settings

Click Back on menus to save updated settings.

CAUTION: Heat or Moisture Damage Risk

Do not install the DVR in a location where the unit is exposed to excessive heat or moisture. Installation close

to extreme heat or moisture will void the product warranty.

Route the wiring and cables away from sharp edges that might damage the insulation. Avoid sharp bends in

the cable.

Contact Seon before attaching the DVR to other equipment in the vehicle.

Camera Views

DVR hard drive

Door lock

Locking front cover

(reversible)

Mounting plate

Cable cover

Cable grommets

Knockouts

TL DVR

Portable

Video Monitor

USB Mouse

Connect a portable video monitor to VIDEO OUT on the TL front panel

Connect a USB mouse to the USB mouse port on the TL front panel

Right-click anywhere in this view to access DVR menus.

Return to this view after updating menus.

1 Main Menu 2 Configuration Menu

3 Time/Date 4 Titles/Display

5 Record 6 Cameras

7 Signals 8 Alarms

Click Configuration to access the

Configuration menu.

Click Time/Date to access the

Time and Date menu.

Time Format: Choose 12 or 24

hour display.

Time: Input the correct time.

Date Format: Select the date

format.

Date: Input the date.

Note: When GPS is installed and

GPS time is selected in the Alarm/

Signal Speed and GPS settings

menus, then the date and time

automatically update when the GPS

detects satellites.

Auto Daylight Saving: Leave this

On and at default dates unless in an

area that does not use daylight savings (ex: Arizona, Saskatchewan).

Click Back to save the menu settings. In the Configuration menu, click Title/Display.

Main Title: Enter the bus number.

Main Title Display: Leave On.

Camera 1-4: Enter camera titles

that describe the views they are

recording, such as:

Front

Step

Mid

Rear

Click Back to save the menu

settings.

In the Configuration menu, click

Record.

Repeat Record: Leave On for the

hard drive to record over the first

recordings when it is full.

Record Delay On Time: Leave at

default to let the bus voltage settle

after the bus starts up, to prevent

voltage drops affecting the DVR.

Record Delay Off Time: Set to 10-

20 minutes to keep the DVR and

cameras on after the ignition turns off

to record the bus post-trip check.

Power Delay Off Time: This starts

up after Record Delay Off time ends.

If Wi-Fi is used, set to 2 hours or

more. If no Wi-fi, leave at default.

Alarm Partition Size: Leave Off unless instructed otherwise.

Leave AnalogRecord2 at 5 FPS unless instructed otherwise. If the customer does not

have Wi-fi or cellular remote DVR access, set to Off.

Click Camera to access camera settings.

Set unused Channel speeds to Off,

so the DVR will not generate video

loss events.

New titles will display here as well as

on the camera view overlays.

Speed: Leave the channel speed at

default settings unless you have

special requirements.

Resolution: Leave the channel

resolution at default settings unless

you have special requirements.

Quality: Leave the channel quality

at default settings unless you have

special requirements.

Audio: Leave audio settings On unless the camera is mounted on the exterior of the

vehicle.

Click Back to save the Camera and Record menu settings and to return to the

Configuration menu. In the Configuration menu, click Alarm/Signal. In the Alarms

and Signals menu, click Signals.

Label: For signals 1-5, select from: LT

left turn, STP stop, BRK brake, WRN

warning light, and RT right turn.

The labels can be edited.

Signals 6-10 are available for

advanced signal wiring if required.

Maximum 3 character.

Level: Set all signal levels as required.

Choose Active High if the circuit you

are installing into rests at 0 VDC and

goes to 12 VDC when active.

Choose Active Low if the circuit rests at

12 VDC and drops to 0 VDC when

active.

Alarm: If a signal is used to trigger an alarm, that alarm’s input must also be set up in

the Alarms menu.

Click Back to save the menu settings. In the Alarms and Signals menu, click Alarms.

Set unused Channel speeds to

Off, so the DVR will not generate

video loss events.

Alarm: Alarm 1 comes from the

DVR alarm button. Alarm 2-4 can

come from signals.

Duration:

Applies to Alarm 1 only. Set

the Duration for how long the DVR will

record video flagged as an alarm.

Speed, Quality, and Resolution:

For each alarm, select higher

settings for better video while the

alarm is recording.

Input: Applies to Alarm 1 only.

Choose Normally Open or Normally Closed, depending on the switch type used.

Pre-Alarm: Select how many seconds of pre-alarm video is included in the flagged

alarm recording.

Email: Leave at default unless instructed otherwise.

Wake: Leave at default unless instructed otherwise.

Click Back to save the menu settings. In the Alarms and Signals menu, click Speed.

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

SEON Trooper TL4 Installationsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Digitale Videorecorder (DVR) SEON Trooper TL4